ford explorer key battery（2018 Ford Key Battery）

List of contents of this article

• ford explorer key battery
• ford explorer key battery 2018
• ford explorer key battery 2016
• ford explorer key battery 2017
• ford explorer key battery dead

ford explorer key battery

The Ford Explorer is a popular SUV that comes equipped with a keyless entry system. This system allows drivers to unlock and start their vehicle without physically inserting a key into the ignition. However, like any electronic device, the key fob for the Ford Explorer requires a battery to function properly.

The key fob for the Ford Explorer uses a small lithium-ion battery, which provides power to the remote control functions. Over time, the battery may lose its charge and need to be replaced. Fortunately, replacing the battery in a Ford Explorer key fob is a relatively simple process.

To replace the battery in a Ford Explorer key fob, you will need a small flathead screwdriver and a replacement battery. The battery type required for the key fob is typically a CR2032, which is widely available at most stores.

Start by locating the small slot on the side of the key fob. Insert the flathead screwdriver into the slot and gently twist it to pry open the key fob. Be careful not to apply too much force, as you don’t want to damage the key fob.

Once the key fob is open, you will see the battery compartment. Remove the old battery by gently pushing it out or using the screwdriver to pry it out. Take note of the battery’s orientation, as you will need to insert the new battery in the same way.

Insert the new battery into the compartment, making sure it is securely in place. Close the key fob by aligning the two halves and pressing them together until they snap into place.

After replacing the battery, test the key fob to ensure it is working properly. Press the buttons on the key fob to lock and unlock the doors, as well as to start the vehicle remotely if applicable. If the key fob is not functioning as expected, double-check the battery’s orientation and placement.

In conclusion, the Ford Explorer key fob uses a small lithium-ion battery that may need to be replaced over time. By following the simple steps outlined above, you can easily replace the battery in your Ford Explorer key fob and continue enjoying the convenience of keyless entry and remote start functions.

ford explorer key battery 2018

The Ford Explorer is a popular SUV known for its reliability and performance. Like most modern vehicles, the 2018 Ford Explorer comes with a keyless entry system that requires a key fob to unlock and start the car. The key fob uses a small battery to transmit signals to the vehicle, allowing you to lock and unlock the doors, as well as start the engine.

The key fob battery in the 2018 Ford Explorer is a CR2032 lithium coin cell battery. This type of battery is commonly used in various electronic devices and is readily available at most stores. Replacing the key fob battery is a simple process that can be done at home without the need for any special tools.

To change the key fob battery in your 2018 Ford Explorer, follow these steps:

1. Locate the small slot on the side of the key fob. This slot is used to open the key fob and access the battery compartment.

2. Insert a small flathead screwdriver or a coin into the slot and gently pry open the key fob. Be careful not to damage the key fob or the battery compartment.

3. Once the key fob is open, you will see the battery compartment. Remove the old battery by gently pushing it out or using a small tool to pop it out.

4. Take the new CR2032 battery and insert it into the battery compartment, making sure the positive (+) side is facing up.

5. Close the key fob by aligning the two halves and pressing them together until they snap into place.

6. Test the key fob by pressing the buttons to ensure it is working properly.

It is recommended to replace the key fob battery if you notice any signs of a weak or dying battery, such as reduced range when unlocking or starting the vehicle. Additionally, it is a good idea to keep a spare battery on hand in case of an emergency.

Overall, changing the key fob battery in a 2018 Ford Explorer is a quick and straightforward process that can be done by anyone. By following these simple steps, you can ensure that your key fob is always functioning properly, allowing you to enjoy the convenience of keyless entry and start in your Ford Explorer.

ford explorer key battery 2016

The Ford Explorer key battery for the year 2016 is a crucial component of the vehicle’s key fob. The key fob is a remote control device that allows the driver to lock and unlock the car, as well as start the engine from a distance. To ensure the key fob functions properly, it is essential to have a fully charged battery.

To replace the key battery in a 2016 Ford Explorer, follow these simple steps:

1. Identify the type of battery: The 2016 Ford Explorer key fob typically requires a CR2032 battery. It is important to verify the battery type before purchasing a replacement.

2. Obtain a new battery: Purchase a CR2032 battery from an automotive store or online retailer. Ensure that the battery is fresh and has not expired.

3. Prepare for replacement: Find a small screwdriver or a coin with a flat edge. This will be used to open the key fob and access the battery compartment.

4. Open the key fob: Locate the small slot or seam on the side of the key fob. Insert the screwdriver or coin and gently twist to pry open the key fob. Be careful not to damage the fob or injure yourself during this process.

5. Replace the battery: Once the key fob is open, you will see the battery compartment. Carefully remove the old battery and replace it with the new CR2032 battery. Ensure the positive (+) side of the battery is facing up.

6. Close the key fob: Align the two halves of the key fob and press them together firmly until they snap back into place. Make sure it is securely closed to prevent any water or dust from entering.

7. Test the key fob: Stand near your vehicle and test the key fob by pressing the lock or unlock buttons. If the vehicle responds accordingly, the battery replacement was successful.

Remember to dispose of the old battery properly and keep it away from children and pets. It is recommended to replace the key battery every 1-2 years or as needed, depending on usage.

By following these steps, you can easily replace the key battery in your 2016 Ford Explorer and ensure that your key fob functions optimally.

ford explorer key battery 2017

The Ford Explorer 2017 model comes with a keyless entry system, which means it does not require a traditional key to start the vehicle. Instead, it uses a key fob that communicates with the car’s computer system. While the key fob does not have a battery that needs to be replaced, it does require a battery to function properly.

The key fob for the Ford Explorer 2017 uses a small, round battery known as a CR2032 battery. This type of battery is commonly used in various electronic devices and can be found at most electronics stores or automotive retailers. Replacing the battery in the key fob is a simple process that can be done at home.

To replace the battery, you will need a small flathead screwdriver or a coin. Start by locating the small slot on the side of the key fob. Insert the screwdriver or coin into the slot and gently twist it to separate the two halves of the key fob. Be careful not to apply too much force to avoid damaging the key fob.

Once the key fob is open, you will see the CR2032 battery. Carefully remove the old battery and replace it with a new one, ensuring that the positive (+) side is facing up. Close the key fob by aligning the two halves and pressing them together until they snap into place.

After replacing the battery, test the key fob by pressing the buttons to lock or unlock the vehicle. If the buttons are not working, double-check that the battery is properly installed. If the issue persists, it may be necessary to consult a Ford dealership or a professional automotive locksmith for further assistance.

It is recommended to keep a spare battery on hand, as the key fob battery can die unexpectedly. Additionally, it is important to note that the battery life can vary depending on usage. On average, the CR2032 battery in the Ford Explorer 2017 key fob should last for several years before needing replacement.

In conclusion, the Ford Explorer 2017 key fob uses a CR2032 battery that can be easily replaced at home. By following the simple steps outlined above, you can ensure that your key fob continues to function properly and provides convenient access to your vehicle.

ford explorer key battery dead

If the key battery of your Ford Explorer is dead, there are a few steps you can take to resolve the issue. Here is what you can do:

1. Identify the problem: If your key battery is dead, you may notice that the key fob is no longer working. The buttons on the key fob won’t unlock or lock the doors, and the remote start feature won’t function.

2. Replace the battery: To resolve this issue, you will need to replace the dead battery in your key fob. Start by locating the small slot or button on the key fob that allows you to open it. Once opened, carefully remove the old battery and replace it with a new one. Make sure to use the correct battery type as specified in your vehicle’s manual.

3. Test the key fob: After replacing the battery, test the key fob to ensure it is working properly. Press the buttons to lock and unlock the doors, and check if the remote start feature is functional. If everything is working as expected, you have successfully resolved the issue.

4. Consider a spare key: If you frequently encounter problems with your key fob battery, it may be a good idea to have a spare key. This way, you can easily switch to the spare key if the battery in your primary key fob dies again. Having a spare key can save you from any inconvenience caused by a dead battery.

5. Seek professional help: If you have followed the above steps and the key fob is still not working, it may be necessary to seek professional assistance. Visit your local Ford dealership or an automotive locksmith who specializes in key fob repairs. They will have the expertise and tools to diagnose and fix any underlying issues with your key fob.

Remember, it is always a good idea to regularly check the battery in your key fob to avoid any unexpected inconveniences.